Blog Archives

Voting for AU 2017 Classes Open!

Hey everyone!  The call for proposals for Autodesk University 2017 is closing, and the time for voting has begun.  This is new this year.  In previous years the selection committee did all of the hard work of selecting classes.  This

Tagged with: , ,
Posted in Autodesk Community, Autodesk University, General, Show All, Uncategorized

Almost that time again….

Wow, it seems like just a few weeks ago that we were in Las Vegas for Autodesk University 2016.  It was another great week, so full of classes, networking and other activities that I didn’t even have time to write

Tagged with: ,
Posted in Autodesk Community, Autodesk University, General, Show All

Autodesk Knowledge Network 

Do you know what this is?  The AKN , as it is commonly known, is a vast storehouse of product knowledge related to the entire universe of Autodesk Software.  Filled with articles, blog posts, Screencast videos and so much more.

Posted in Autodesk Community, Autodesk Knowledge Network, Autodesk Screencast, General, Show All

Instrument Loops in AutoCAD P&ID

Hello! After one of the craziest summers I have seen since I have been on this job, I finally got a chance last week to get back into setting up my AutoCAD P&ID software.  It took a little while just

Tagged with:
Posted in AutoCAD P&ID, General, Show All

Happy October – 6 weeks to AU 2016

Only 6 more weeks (roughly) until Autodesk University 2016.  If you haven’t already registered, you should consider it.  This is three days of learning, networking and general fun.  Held again this year at the Venetian Casino and Resort in Las

Tagged with: , ,
Posted in Autodesk Community, Autodesk University, General, Show All

Change Physical Properties on Content Center Parts

So…. you have a part in your Content Center.  It’s a purchased part, and you got a Step file from a supplier, which you authored, and published and tucked away neat and clean.  The block was a fairly “dumb” part.

Tagged with: , ,
Posted in Autodesk Inventor, Autodesk Vault, Content Center, General, Show All

Autodesk University 2015 – Wrap up

Well,… I’m safely home and back to work, and I haven’t had 5 minutes to write anything until now.  I’m going to do a very quick wrap up of the last few days of Autodesk University, so bear with me.

Tagged with: , , ,
Posted in Autodesk Community, Autodesk University, General, Show All

Autodesk University 2015 – Day 4

Ok,… running late.  It’s actually 10:23 am on Day 5 (for me).  Yesterday was a very busy day.  Classes all morning, some very good ones that have me thinking about some things I might want to look into when i

Tagged with: , , ,
Posted in Autodesk University, General, Show All

Autodesk University 2015 – Day 3

Back again!  As I start to write this post, it’s 4:30 pm Tuesday December 1.  I’ve been awake for roughly 12 hours, but then…. it’s Vegas and AU… no one sleeps here!  This has been a full day so far,

Tagged with: , ,
Posted in Autodesk Community, Autodesk University, General, Show All

Autodesk University 2015 – Day 2

Hello again! Autodesk University day 2, which for most is the day they arrive and check in, was a busy day for me.  I checked in early and got this years speaker shirt, along with the all important cup of

Tagged with:
Posted in Autodesk Community, Autodesk University, General
Post Archive
Follow me on Twitter
CADproTips

Providing the CAD knowledge you need to succeed.

The CAD Setter Out

AutoCAD and Inventor Tips, Tricks & Tutorials.

Design & Motion

Design and Manufacturing solutions through Digital Prototyping and Interoperability

CADToolbox.com

Dedicated to the Autodesk Inventor Community